Hellwig Sway Bar 7266 Manuel d'utilisateur télécharger pdf

TORQUE TABLE

BOLT SIZE: 3/8” = 20-30 ft. lbs. – 7/16” = 35-45 ft. lbs. – ½” = 50-70 ft. lbs. – 9/16” = 70-90 ft. lbs.

SAFETY: BEFORE STARTING YOUR INSTALLATION, BE SURE TO SET PARKING BRAKE AND CHOCK TIRES.

NOTE: TO EASE INSTALLATION AND TO PROPERLY ADJUST BAR, THE WEIGHT OF THE VEHICLE MUST BE

ON THE SUSPENSION, AS IF DRIVING DOWN THE ROAD. DO NOT RAISE VEHICLE BY FRAME.

NOTE: THIS UNIT IS DESIGNED TO MOUNT TO THE REAR OF THE AXLE TUBES WITH THE ARMS OF THE BAR

TOWARD THE REAR OF THE VEHICLE. THE HUMP SHOULD TILT SLIGHTLY DOWNWARD.

NOTE: THIS KIT INCLUDES LOCK NUTS WHICH REQUIRE TIGHTENING WITH A WRENCH AFTER BEING STARTED

BY HAND.

1. As shown in photo one (1), place D-shaped poly-bushings onto straight areas of the bar on each side of center hump. After installing D-

bushings onto bar, place U-plates on D-bushings.

2. Place U-bolts on axle tubes next to casting as shown in photo two (2). When installing U-bolts, be sure to put U-bolts under any

brake lines, wires or hoses on the axle to avoid any possible damage.

3. Before installing saddle brackets, remove passenger side brake line from clip and reposition brake line so that it will

clear the saddle bracket as shown in photo two (2). Secure brake line with tie strap.

4. Place saddle brackets on axle by inserting legs of U-bolts into the holes in saddle brackets. Saddle brackets must be installed so that one

leg of the saddle bracket is located on the cast center section with the leg just inside the raised lip on the casting. See photo two (2)

5. Raise bar and place D-bushings on saddle brackets by inserting legs of U-bolts through holes in U-plates. Install flat washers and hex

nuts provided on U-bolts. Do not use locknuts provided in kit on axle U-bolts. LEAVE LOOSE AT THIS TIME to allow for

adjustment later.

6. Locate existing spare tire crossmember on vehicle frame. Place square U-bolt over frame rail just behind crossmember with legs of U-

bolt pointing downward.

7. Insert legs of U-bolt into slotted holes of the hanger brackets. Install hanger brackets with clevis inboard of frame rail and toward front

of vehicle as shown in photo three (3). Attach using 1/2” lock nuts. LEAVE LOOSE for adjustment later.

8. Install bushings and spacer tube into the sleeve in end link. Place end link into clevis with offset inboard. Attach end link with 7/16 X 2

1/4” capscrew. See picture three (3).

1 2

Tie Strap

Brake Line

Clip

INSTALLATION INSTRUCTIONS

7266 Rear Stabilizer Bar

Thank you for purchasing a quality Hellwig Product.

PLEASE READ THIS INSTRUCTION SHEET COMPLETELY BEFORE STARTING YOUR INSTALLATION

1 2

INSTALLATION INSTRUCTIONS 1

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

TORQUE TABLEBOLT SIZE: 3/8” = 20-30 ft. lbs. – 7/16” = 35-45 ft. lbs. – ½” = 50-70 ft. lbs. – 9/16” = 70-90 ft. lbs.SAFETY: BEFORE STARTING YOUR INSTA

Page 2

9. Thread jam nut and hex nut on to threads of end link far enough to mount flat washers and bushings to the end of sway bar as shown inphoto three (3

Commentaires sur ces manuels

Pas de commentaire

Hellwig Sway Bar 7266 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Hellwig Sway Bar 7266. Hellwig Sway Bar 7266 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Hellwig Sway Bar 7266